kpexa
Newbie | Редактировать | Профиль | Сообщение | Цитировать | Сообщить модератору
[more] [more]
Цитата: Привет!!! попробовал на всех 4-х сата портах одна и таже ошибка, потом у друга взял переходник USB-SATA и эта ошибка ушла, и однажды в винде ССД запустился обнаружился и со своими файлами и разделами, и вот что выдала программа sf.info v0.431a,
Drive: 1(USB)
Model: ADATA XM11 256GB-V2
Fw : 5.0.2a
Size : 244198 MB
--- SandForce specific ---
Signature : 158-0-27140
Controller : SF-2000
HW Revision : 200026BB (B01)
Try to unlock the drive (default)...
Drive unlocked (default)!
FW : [Y37ABBF0 ]
FW string : [B:FW_PPRO_MP_5_0_0:FW_PPRO_Y_3_7_Release-419988 ]
Config file : [cfg/cfg_MLC_Micron_64Gb_MT29F256G08CMCABH2_2Q_4C_1D ]
ROM Revision: [20D ]
NAND ID : 0x2c, 0x88, 0x4, 0x4b, 0xa9, 0x0, 0x0, 0x0
Page Size : 8640
NAND CE : 4
Sector/Page : 8
Die/CE : 1
Block/Die : 2048
Page/Block : 256
Raw Size : 536870912
NAND Max EC : 3000
Max PE Cycles : need fw.360+/520+
Cur PE Cycles : need fw.360+/520+
Life In Seconds : 0 (Not Set)
LBA Size : 500118192
Sector Size : 512
Sector Align : +0
NAND ID : 0x2c,0x88
Serial Output Control : Default(Off)
Erase R Block : Disable
Panic Handling Enabled : Disable
Panic On SATA Error : Disable
Write Throttling Test Mode: Disable
R.A.I.S.E. : Disable
Flash CE : 32
Bank00: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank01: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank02: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank03: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank04: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank05: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank06: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank07: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank08: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank09: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank10: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank11: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank12: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank13: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank14: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank15: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank16: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank17: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank18: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank19: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank20: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank21: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank22: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank23: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank24: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank25: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank26: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank27: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank28: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank29: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank30: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
Bank31: 0x2c,0x88,0x4,0x4b,0xa9,0x0,0x0,0x0 - Micron 25nm(L74A) MLC 64Gb/CE 64Gb/die
UART freq : 0
SATA Status Coalescing : 0
Compressible data performance tuning option : 0 (no tuning for compr. data)
Serial Output Control : 0 (Default)
Write Speed Limit : 0 (Off)
Led Settings
Activity LED Polarity : 0 (Normal)
Fault LED Polarity : 0 (Normal)
LED Blink Rate : 0 (250ms)
Power Managment Settings
Power Management Version : 0 (SF1)
Sleep command mode : 0 (Default)
IDLE command mode : 0 (Default)
Temperature Sensor Settings
Sensor 1:
Device ID : 2 (LM73)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0n (Default - 65C)
Max Temperature Threshold Level 2 Entry Point (MT2) : 0n (Default - 70C)
Min Temperature Threshold (LT1) : 0n (Default - 0C)
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0 (Default - MT1)
Sensor 2:
Device ID : 0 (Default)
Device Address : 0
Max Temperature Threshold Level 1 Entry Point (MT1) : 0
Max Temperature Threshold Level 2 Entry Point (MT2) : 0
Min Temperature Threshold (LT1) : 0
Max Temperature Threshold Behavior for MT1 (MT1B) : 0 (Default)
Max Temperature Threshold Behavior for MT2 (MT2B) : 0 (Default)
Min Temperature Threshold Behavior (LT1B) : 0 (Default)
Max Temperature Threshold Level 1 Return Point (MTR1): 0
Security Erase Options
Security Erase Behavior : 0 (Default)
Enhanced Security Erase Behavior (Military Erase) : 0 (Default)
SATA Command and Firmware Options
Flush Cache Behavior : 0 (Default)
ATA Security Set Enable : 0 (Default)
Spread Spectrum Clocking Enable : 1 (Off)
SATA Link Handling on Reboot : 0 (Default)
ACS2 Support : 0 (Default)
Failed Secure Unlock Delay Enable : 0 (Default(No delay))
Seek Complete in Error Status : 0 (Default)
Read Long with Retry and without Retry : 0 (Default)
Read Sectors without Retry : 0 (Default)
Write DMA without Retry : 0 (Default)
Write Long with Retry and without Retry : 0 (Default)
Max SATA Link Rate : 0 (Default)
Deterministic Trim Setting : 0 (Default)
Controller Drive Strength Rate : 0 (Default)
PHY Setting : 0 (Default)
Controller Slew Rate : 0 (Default)
Put SIG FIS Delay : 0 (Default)
Set Multiple Handling : 0 (Default)
TRIM Timer Abort : 0 (Enable(Default))
Trim Support/Setting Word 169 Bit 0 : 0 (Default(Firmware default setting))
RDD1 Optimization : 0 (Default)
Security Unlock Drive : 0 (Default(Compare Master Password))
Power Throttling Options
Average Power Level 0-100 : 0
Maximum Power Level 0-100 : 0
Power Throttling Upon Unsafe Shutdown : 0 (Default)
Dynamic Read Scrub
Read Scrub Enabled : 0 (Default (Enabled))
Dynamic Read Scrub End Range1 : 0
Dynamic Read Scrub Rate Range1 : 0
Dynamic Read Scrub End Range2 : 0
Dynamic Read Scrub Rate Range2 : 0
Dynamic Read Scrub End Range3 : 0
Dynamic Read Scrub Rate Range3 : 0
Dynamic Read Scrub End Range4 : 0
Dynamic Read Scrub Rate Range4 : 0
Low Level Format Settings
Number of entries in Max LBA Setting : 1
Sub-Sector Size [0] : 512
Pattern Size [0] : 2
Sub-Sector and Patterns per sector [0] : 0
Max LBA Count [0] : 500118192
Host Protected Area
Host Protected Access : 0 (Always Reset HPA State On COMRESET)
End of Life Behavior
Enable End of Life : 0 (Default (EOL Enabled))
EOL Threshold 1 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Light Write Throttling))
EOL Threshold 2 Type : 0 (Default (SSD Life Left))
EOL Threshold 1 Percentage : 0
EOL Threshold 1 Behavior : 0 (Default (Heavy Write Throttling))
CDU Smart settings: default
Fab Defect list entry : 23
Idx Bus CE Die Plane Block Lane3210 Defects
0 0 0 0 0 45 BBBB 4
1 1 0 0 0 45 BBBB 4
2 0 0 0 1 45 BBBB 4
3 1 0 0 1 45 BBBB 4
4 0 1 0 0 45 BBBB 4
5 1 1 0 0 45 BBBB 4
6 0 1 0 1 45 BBBB 4
7 1 1 0 1 45 BBBB 4
8 0 2 0 0 45 BBBB 4
9 1 2 0 0 45 BBBB 4
10 0 2 0 1 45 BBBB 4
11 1 2 0 1 45 BBBB 4
12 0 3 0 0 45 BBBB 4
13 1 3 0 0 45 BBBB 4
14 0 3 0 1 45 BBBB 4
15 1 3 0 1 45 BBBB 4
16 0 3 0 1 506 __B_ 1
17 0 1 0 0 560 _B__ 1
18 0 2 0 0 685 ___B 1
19 1 0 0 0 1611 __B_ 1
20 1 0 0 1 1611 __B_ 1
21 0 3 0 0 1631 __B_ 1
22 0 3 0 0 1699 B___ 1
Fab Defects : 71
User Defect list entry: 0
Panic Dumps : 3
Panic Dumps list:
Idx Accurev SyncCode UnlockLevel Size DataSize EPA Log Ok CRC Ok
0 -1 0xffffffff 0xffffffff -1 -1 0x00020002 0x0000 0x0000
1 419988 0x0e21c576 0xffffff00 3388 2956768 0x20020002 0x0001 0x0001
2 419988 0x0e21c576 0xffffff00 3388 2956768 0x00020082 0x0001 0x0001
3 419988 0x0e21c576 0xffffff00 3388 2956768 0x20020082 0x0001 0x0001
Panic Dump 1 Accumulative Time: 285 days 0:47:13
Panic Dump 1 Total Up Time : 285 days 0:47:13
Panic Dump 2 Accumulative Time: 285 days 1:00:08
Panic Dump 2 Total Up Time : 285 days 1:00:08
Panic Dump 3 Accumulative Time: 285 days 0:56:55
Panic Dump 3 Total Up Time : 285 days 0:56:55
MST settings not exist.
MST result not exits.
|
Всего записей: 6 | Зарегистр. 02-07-2020 | Отправлено: 15:38 06-07-2020 | Исправлено: kpexa, 15:41 06-07-2020 |
|
